Remove trailing whitespace
This commit is contained in:
Sam Chesney
@@ -25,7 +25,7 @@ sc_usb_audio Change Log
|
||||
|
||||
6.20.0
|
||||
------
|
||||
- RESOLVED: Intra-frame sample delays of 1/2 samples on input streaming in TDM mode
|
||||
- RESOLVED: Intra-frame sample delays of 1/2 samples on input streaming in TDM mode
|
||||
- RESOLVED: Build issue with NUM_USB_CHAN_OUT set to 0 and MIXER enabled
|
||||
- RESOLVED: SPDIF_TX_INDEX not defined build warning only emitted when SPDIF_TX defined
|
||||
- RESOLVED: Failure to enter DFU mode when configured without input volume control
|
||||
@@ -51,7 +51,7 @@ sc_usb_audio Change Log
|
||||
------
|
||||
- ADDED: Call to UserBufferManagement()
|
||||
- ADDED: PDM_MIC_INDEX in devicedefines.h and usage
|
||||
- CHANGE: pdm_buffer() task now combinable
|
||||
- CHANGE: pdm_buffer() task now combinable
|
||||
- CHANGE: Audio I/O task now takes i_dsp interface as a parameter
|
||||
- CHANGE: Removed built-in support for A/U series internal ADC
|
||||
- CHANGE: User PDM Microphone processing now uses an interface (previously function call)
|
||||
@@ -67,45 +67,45 @@ sc_usb_audio Change Log
|
||||
|
||||
6.15.0
|
||||
------
|
||||
|
||||
- RESOLVED: UAC 1.0 descriptors now support multi-channel volume control (previously were
|
||||
|
||||
- RESOLVED: UAC 1.0 descriptors now support multi-channel volume control (previously were
|
||||
hard-coded as stereo)
|
||||
- CHANGE: Removed 32kHz sample-rate support when PDM microphones enabled (lib_mic_array
|
||||
currently does not support non-integer decimation factors)
|
||||
|
||||
6.14.0
|
||||
------
|
||||
- ADDED: Support for for master-clock/sample-rate divides that are not a power of 2
|
||||
(i.e. 32kHz from 24.567MHz)
|
||||
- ADDED: Extended available sample-rate/master-clock ratios. Previous restriction was <=
|
||||
512x (i.e. could not support 1024x and above e.g. 49.152MHz MCLK for Sample Rates
|
||||
- ADDED: Support for for master-clock/sample-rate divides that are not a power of 2
|
||||
(i.e. 32kHz from 24.567MHz)
|
||||
- ADDED: Extended available sample-rate/master-clock ratios. Previous restriction was <=
|
||||
512x (i.e. could not support 1024x and above e.g. 49.152MHz MCLK for Sample Rates
|
||||
below 96kHz) (#13893)
|
||||
- ADDED: Support for various "low" sample rates (i.e. < 44100) into UAC 2.0 sample rate
|
||||
list and UAC 1.0 descriptors
|
||||
- ADDED: Support for the use and integration of PDM microphones (including PDM to PCM
|
||||
conversion) via lib_mic_array
|
||||
- ADDED: Support for the use and integration of PDM microphones (including PDM to PCM
|
||||
conversion) via lib_mic_array
|
||||
- RESOLVED: MIDI data not accepted after "sleep" in OSX 10.11 (El Capitan) - related to sc_xud
|
||||
issue #17092
|
||||
- CHANGE: Asynchronous feedback system re-implemented to allow for the first two ADDED
|
||||
changelog items
|
||||
- CHANGE: Hardware divider used to generate bit-clock from master clock (xCORE-200 only).
|
||||
changelog items
|
||||
- CHANGE: Hardware divider used to generate bit-clock from master clock (xCORE-200 only).
|
||||
Allows easy support for greater number of master-clock to sample-rate ratios.
|
||||
- CHANGE: module_queue no longer uses any assert module/lib
|
||||
|
||||
6.13.0
|
||||
------
|
||||
- ADDED: Device now uses implicit feedback when input stream is available (previously explicit
|
||||
feedback pipe always used). This saves chanend/EP resources and means less processing
|
||||
feedback pipe always used). This saves chanend/EP resources and means less processing
|
||||
burden for the host. Previous behaviour available by enabling UAC_FORCE_FEEDBACK_EP
|
||||
- RESOLVED: Exception when SPDIF_TX and ADAT_TX both enabled due to clock-block being configured
|
||||
after already started. Caused by SPDIF_TX define check typo
|
||||
- RESOLVED: DFU flag address changed to properly conform to memory address range allocated to
|
||||
- RESOLVED: DFU flag address changed to properly conform to memory address range allocated to
|
||||
apps by tools
|
||||
- RESOLVED: Build failure when DFU disabled
|
||||
- RESOLVED: Build issue when I2S_CHANS_ADC/DAC set to 0 and CODEC_MASTER enabled
|
||||
- RESOLVED: Typo in MCLK_441 checking for MIN_FREQ define
|
||||
- CHANGE: Mixer and non-mixer channel comms scheme (decouple <-> audio path) now identical
|
||||
- CHANGE: Input stream buffering modified such that during overflow older samples are removed
|
||||
- CHANGE: Input stream buffering modified such that during overflow older samples are removed
|
||||
rather than ignoring most recent samples. Removes any chance of stale input packets
|
||||
being sent to host
|
||||
- CHANGE: module_queue (in sc_usb_audio) now uses lib_xassert rather than module_xassert
|
||||
@@ -116,17 +116,17 @@ sc_usb_audio Change Log
|
||||
- RESOLVED: Build error when I2S_CHANS_ADC or I2S_CHANS_DAC set to 0 and CODEC_MASTER enabled
|
||||
|
||||
6.12.5
|
||||
------
|
||||
------
|
||||
- RESOLVED: Stream issue when NUM_USB_CHAN_IN < I2S_CHANS_ADC
|
||||
|
||||
6.12.4
|
||||
------
|
||||
------
|
||||
- RESOLVED: DFU fail when DSD enabled and USB library not running on tile[0]
|
||||
|
||||
6.12.3
|
||||
------
|
||||
- RESOLVED: Method for storing persistent state over a DFU reboot modified to improve resilience
|
||||
against code-base and tools changes
|
||||
- RESOLVED: Method for storing persistent state over a DFU reboot modified to improve resilience
|
||||
against code-base and tools changes
|
||||
|
||||
6.12.2
|
||||
------
|
||||
|
||||
Reference in New Issue
Block a user